
Customer Use (0x6) - (0x207)
  Customer Use
    Customer Use Word 1   0x207 (0x207)
    Customer Use Word 2   0x0 (0x0)

Interrupt Mask for I2C1 (0x16) - (0x2000008)
  Interrupt Mask for I2C1
    Soft Reset                                       False (0x0)
    Hard Reset                                       False (0x0)
    Power Path Event                                 False (0x0)
    Plug Insert or Removal                           True (0x1)
    PR Swap Complete                                 False (0x0)
    DR Swap Complete                                 False (0x0)
    Awoken by Host                                   False (0x0)
    RDO Received from Sink                           False (0x0)
    Built-In Self Test                               False (0x0)
    Overcurrent Event                                False (0x0)
    Attention Received                               False (0x0)
    Vendor-Defined Message Received                  False (0x0)
    New Contract as Consumer                         False (0x0)
    New Contract as Provider                         False (0x0)
    Source Capabilities Message Ready                False (0x0)
    Sink Capabilities Message Ready                  False (0x0)
    Swap Requested                                   False (0x0)
    BIST Message Ignored                             False (0x0)
    GotoMin Received                                 False (0x0)
    USB Host Present                                 False (0x0)
    USB Host Present No Longer                       False (0x0)
    High Voltage Warning                             False (0x0)
    Power Path Switch Changed                        False (0x0)
    Power Status Update                              False (0x0)
    Data Status Update                               True (0x1)
    Status Update                                    False (0x0)
    PD Status Update                                 False (0x0)
    ADC Low Threshold                                False (0x0)
    ADC High Threshold                               False (0x0)
    CMD1 Complete                                    False (0x0)
    CMD2 Complete                                    False (0x0)
    Error: Device Incompatible                       False (0x0)
    Error: Cannot Provide Voltage or Current         False (0x0)
    Error: Cannot Provide Voltage or Current Later   False (0x0)
    Error: Power Event Occurred                      False (0x0)
    Error: Missing Get Capabilities Message          False (0x0)
    Error: Protocol Error                            False (0x0)
    Error: Message Data                              False (0x0)
    Error: Discharge Failed                          False (0x0)
    Sink Transition Complete                         False (0x0)
    Error: Unable to Source                          False (0x0)
    User SVID Mode Entered                           False (0x0)
    User SVID Mode Exited                            False (0x0)
    User SVID Attention VDM Received                 False (0x0)
    User SVID Other VDM Received                     False (0x0)

Interrupt Mask for I2C2 (0x17) - (0x2000008)
  Interrupt Mask for I2C2
    Soft Reset                                       False (0x0)
    Hard Reset                                       False (0x0)
    Power Path Event                                 False (0x0)
    Plug Insert or Removal                           True (0x1)
    PR Swap Complete                                 False (0x0)
    DR Swap Complete                                 False (0x0)
    Awoken by Host                                   False (0x0)
    RDO Received from Sink                           False (0x0)
    Built-In Self Test                               False (0x0)
    Overcurrent Event                                False (0x0)
    Attention Received                               False (0x0)
    Vendor-Defined Message Received                  False (0x0)
    New Contract as Consumer                         False (0x0)
    New Contract as Provider                         False (0x0)
    Source Capabilities Message Ready                False (0x0)
    Sink Capabilities Message Ready                  False (0x0)
    Swap Requested                                   False (0x0)
    BIST Message Ignored                             False (0x0)
    GotoMin Received                                 False (0x0)
    USB Host Present                                 False (0x0)
    USB Host Present No Longer                       False (0x0)
    High Voltage Warning                             False (0x0)
    Power Path Switch Changed                        False (0x0)
    Power Status Update                              False (0x0)
    Data Status Update                               True (0x1)
    Status Update                                    False (0x0)
    PD Status Update                                 False (0x0)
    ADC Low Threshold                                False (0x0)
    ADC High Threshold                               False (0x0)
    CMD1 Complete                                    False (0x0)
    CMD2 Complete                                    False (0x0)
    Error: Device Incompatible                       False (0x0)
    Error: Cannot Provide Voltage or Current         False (0x0)
    Error: Cannot Provide Voltage or Current Later   False (0x0)
    Error: Power Event Occurred                      False (0x0)
    Error: Missing Get Capabilities Message          False (0x0)
    Error: Protocol Error                            False (0x0)
    Error: Message Data                              False (0x0)
    Error: Discharge Failed                          False (0x0)
    Sink Transition Complete                         False (0x0)
    Error: Unable to Source                          False (0x0)
    User SVID Mode Entered                           False (0x0)
    User SVID Mode Exited                            False (0x0)
    User SVID Attention VDM Received                 False (0x0)
    User SVID Other VDM Received                     False (0x0)

System Power State (0x20) - (0x0)
  System Power State
    Sleep Mode (When Allowed)   Do Not Sleep (0x0)

System Configuration (0x28) - (0x1414000006059d00d82a1508f7093f038d)
  System Configuration
    Port Information                                         Toggles R_p/R_d on CC (with try.Src), supports data/power role swap (0x5)
    Receptacle Type                                          Standard fully-featured USB-C receptacle (0x1)
    Type-C Current                                           3 A (strongest pullup) (0x2)
    Type-C Current OCP Peak Current                          100% (0x0)
    V_CONN Supported                                         VCONN supported as DFP/UFP (accept VCONN_Swap requests) (0x3)
    High Voltage Warning Level                               Warning when source VBUS voltage exceeds 10% from nominal (0x0)
    Low Voltage Warning Level                                Warning when source VBUS Voltage dips below 10% from nominal (0x0)
    Over Voltage Protection Trip Point                       24 V (0x3f)
    Over Voltage Protection Usage                            Disconnect VBUS if voltage exceeds OVPTripPoint (0x0)
    PP_5V0 Configuration                                     PP_5V0 switch configured for output (0x1)
    PP_HV Configuration                                      PP_HV switch configured for input (0x2)
    PP_EXT Configuration                                     PP_EXT not used (disabled) (0x0)
    BC 1.2 Enable                                            True (0x1)
    USB RP Enable                                            True (0x1)
    USB EP Enable                                            True (0x1)
    USB3.0/3.1 Rate                                          USB3 Gen2 signaling rate supported (0x2)
    USB2.0 Supported                                         True (0x1)
    Audio Accessory Support                                  True (0x1)
    Debug Accessory Support                                  True (0x1)
    Powered Accessory Support                                False (0x0)
    Rsense (External Sense Resistor)                         10 mOhm (0x0)
    Try.Src (Try Source Support)                             False (0x0)
    USB2.0 Endpoint Billboard Enable                         True (0x1)
    External Power Path Over-Current Timeout Enable          Enabled (0x1)
    External Power Path Over-current Timeout                 640 us (0x4)
    Reset Z Timeout Count                                    2 (0x2)
    Reset Z Timeout Clock                                    640 us (0x1)
    Vout3V3 (3.3 V output) threshold                         2.75 V (0x5)
    Vout3V3 (3.3 V output) enable                            False (0x0)
    Sense Disconnect on CC (in addition to VBUS) when Sink   False (0x0)
    Set Under-voltage Protection to 4.5V always              False (0x0)
    Under-voltage Protection Trip Point, PP_5V               20% (0x3)
    Under-voltage Protection Usage, PP_HV                    20% (0x3)
    UART Disable                                             UART Enabled (0) (0x0)
    Serial String Index                                      Serial Number String at Index 1 (0x1)
    Product String Index                                     Product String at Index 2 (0x2)
    Manufacturer String Index                                Manufacturer String at Index 3 (0x3)
    Billboard URL String Index                               Billboard URL String at Index 4 (0x4)
    Intel Thuderbolt Billboard String Index                  TBT Billboard String at Index 5 (0x5)
    DisplayPort Billboard String Index                       DisplayPort Billboard String at Index 6 (0x6)
    Custom Vendor ID 1 String Index                          No Custom Vendor ID 1 Billboard String (0x0)
    Custom Vendor ID 2 String Index                          No Custom Vendor ID 2 Billboard String (0x0)
    Custom Vendor ID 3 String Index                          No Custom Vendor ID 3 Billboard String (0x0)
    Custom Vendor ID 4 String Index                          No Custom Vendor ID 4 Billboard String (0x0)
    Internal 5V Power Path Over-Current Timeout Enable       Enabled (0x1)
    Internal 5V Power Path Over-current Timeout              640 us (0x4)
    Internal HV Power Path Over-Current Timeout Enable       Enabled (0x1)
    Internal HV Power Path Over-current Timeout              640 us (0x4)
    Voltage Threshold for Adjustable GPIO Event              0 V (0x0)

Control Configuration (0x29) - (0x77100c450)
  Control Configuration
    PD Mode                               Normal PD Behavior (0x0)
    Externally Powered                    False (0x0)
    Never Sink if Externally Powered      True (0x1)
    Process Swap To Sink                  True (0x1)
    Initiate Swap To Sink                 False (0x0)
    Process Swap To Source                True (0x1)
    Initiate Swap To Source               False (0x0)
    RDO Intrusive Mode                    False (0x0)
    PDO Intrusive Mode                    False (0x0)
    Process VCONN Swap                    True (0x1)
    Initiate VCONN Swap                   False (0x0)
    Process Swap to UFP                   False (0x0)
    Initiate Swap to UFP                  False (0x0)
    Process Swap to DFP                   True (0x1)
    Initiate Swap to DFP                  True (0x1)
    Automatic Sink Capabilities Request   False (0x0)
    Automatic ID Request                  True (0x1)
    Intrusive Alternate Mode Support      False (0x0)
    Force USB Generation 1                False (0x0)
    I2C Timeout Period                    200 mS (0x7)

Transmit Source Capabilities (0x32) - (0x3c12c2601912c00fc01)
  Transmit Source Capabilities
    Tx Source PDO Config
      Number of Source PDOs   1 (0x1)
    Source PDO 1
      Switch Source           Internal 5 volt Power Path (PP_5V) (0x0)
      Maximum Current         3 A (0x12c)
      Voltage                 5 V (0x64)
      Peak Current            100% (0x0)
      reserved                reserved, set 0 (0x0)
      USB Capable             True (0x1)
      USB Suspend Supported   False (0x0)
      Supply Type             Fixed Source (0x0)
    Source PDO 2
      Advertised Mask   Always Advertise (0x1)
      Switch Source     Internal High Voltage Power Path (PP_HV) (0x0)
      Maximum Current   3 A (0x12c)
      Voltage           12 V (0xf0)
      Peak Current      100% (0x0)
      reserved          reserved, set 0 (0x0)
      Supply Type       Fixed Source (0x0)
    Source PDO 3
      Advertised Mask   Always Advertise (0x1)
      Switch Source     Internal High Voltage Power Path (PP_HV) (0x0)
      Maximum Current   0 A (0x0)
      Voltage           0 V (0x0)
      Peak Current      100% (0x0)
      reserved          reserved, set 0 (0x0)
      Supply Type       Fixed Source (0x0)
    Source PDO 4
      Advertised Mask   Always Advertise (0x1)
      Switch Source     Internal High Voltage Power Path (PP_HV) (0x0)
      Maximum Current   0 A (0x0)
      Voltage           0 V (0x0)
      Peak Current      100% (0x0)
      reserved          reserved, set 0 (0x0)
      Supply Type       Fixed Source (0x0)
    Source PDO 5
      Advertised Mask   Always Advertise (0x1)
      Switch Source     Internal High Voltage Power Path (PP_HV) (0x0)
      Maximum Current   0 A (0x0)
      Voltage           0 V (0x0)
      Peak Current      100% (0x0)
      reserved          reserved, set 0 (0x0)
      Supply Type       Fixed Source (0x0)
    Source PDO 6
      Advertised Mask   Always Advertise (0x1)
      Switch Source     Internal High Voltage Power Path (PP_HV) (0x0)
      Maximum Current   0 A (0x0)
      Voltage           0 V (0x0)
      Peak Current      100% (0x0)
      reserved          reserved, set 0 (0x0)
      Supply Type       Fixed Source (0x0)
    Source PDO 7
      Advertised Mask   Always Advertise (0x1)
      Switch Source     Internal High Voltage Power Path (PP_HV) (0x0)
      Maximum Current   0 A (0x0)
      Voltage           0 V (0x0)
      Peak Current      100% (0x0)
      reserved          reserved, set 0 (0x0)
      Supply Type       Fixed Source (0x0)

Transmit Sink Capabilities (0x33) - (0x4001692c4001692c00000000000000000000000000000000000000000002d05a2601905a02)
  Transmit Sink Capabilities
    Sink PDO Count
      Number of Sink PDOs   2 (0x2)
    Sink PDO 1
      Operating Current           0.9 A (0x5a)
      Voltage                     5 V (0x64)
      Peak Current                100% (0x0)
      reserved                    reserved, set 0 (0x0)
      Supply Type                 Fixed Sink (0x0)
      Maximum Operating Current   3 A (0x12c)
      Minimum Operating Current   0.9 A (0x5a)
      Ask For Max                 True (0x1)
    Sink PDO 2
      Operating Current           0.9 A (0x5a)
      Voltage                     9 V (0xb4)
      Peak Current                100% (0x0)
      reserved                    reserved, set 0 (0x0)
      Supply Type                 Fixed Sink (0x0)
      Maximum Operating Current   3 A (0x12c)
      Minimum Operating Current   0.9 A (0x5a)
      Ask For Max                 True (0x1)
    Sink PDO 3
      Operating Current           0 A (0x0)
      Voltage                     0 V (0x0)
      Peak Current                100% (0x0)
      reserved                    reserved, set 0 (0x0)
      Supply Type                 Fixed Sink (0x0)
      Maximum Operating Current   0 A (0x0)
      Minimum Operating Current   0 A (0x0)
      Ask For Max                 False (0x0)
    Sink PDO 4
      Operating Current           0 A (0x0)
      Voltage                     0 V (0x0)
      Peak Current                100% (0x0)
      reserved                    reserved, set 0 (0x0)
      Supply Type                 Fixed Sink (0x0)
      Maximum Operating Current   0 A (0x0)
      Minimum Operating Current   0 A (0x0)
      Ask For Max                 False (0x0)
    Sink PDO 5
      Operating Current           0 A (0x0)
      Voltage                     0 V (0x0)
      Peak Current                100% (0x0)
      reserved                    reserved, set 0 (0x0)
      Supply Type                 Fixed Sink (0x0)
      Maximum Operating Current   0 A (0x0)
      Minimum Operating Current   0 A (0x0)
      Ask For Max                 False (0x0)
    Sink PDO 6
      Operating Current           0 A (0x0)
      Voltage                     0 V (0x0)
      Peak Current                100% (0x0)
      reserved                    reserved, set 0 (0x0)
      Supply Type                 Fixed Sink (0x0)
      Maximum Operating Current   0 A (0x0)
      Minimum Operating Current   0 A (0x0)
      Ask For Max                 False (0x0)
    Sink PDO 7
      Operating Current           0 A (0x0)
      Voltage                     0 V (0x0)
      Peak Current                100% (0x0)
      reserved                    reserved, set 0 (0x0)
      Supply Type                 Fixed Sink (0x0)
      Maximum Operating Current   0 A (0x0)
      Minimum Operating Current   0 A (0x0)
      Ask For Max                 False (0x0)

Autonegotiate Sink (0x37) - (0x16800000000000020015f)
  Autonegotitate Sink
    General Settings
      Autonegotiate Sink Enable            True (0x1)
      Autonegotiate Variable Sink Enable   True (0x1)
      Autonegotiate Battery Sink Enable    True (0x1)
      USB Communication Capable            True (0x1)
      Offer Priority                       Choose Highest Voltage (0x1)
      No USB Suspend                       True (0x1)
      Giveback Flag                        False (0x0)
    Capabilities Mismatch Determination
      Automatically Calculate Min Power Required   True (0x1)
      Minimum Power Required                       8 W (0x20)

Alternate Mode Entry Queue (0x38) - (0x1ff01)
  Alternate Mode Entry Queue
    Alternate Mode Entry Queue record #1
      SVID (Standard or Vendor ID)   0xff01 (0xff01)
      Mode Number                    0x1 (0x1)
    Alternate Mode Entry Queue record #2
      SVID (Standard or Vendor ID)   0x0 (0x0)
      Mode Number                    0x0 (0x0)
    Alternate Mode Entry Queue record #3
      SVID (Standard or Vendor ID)   0x0 (0x0)
      Mode Number                    0x0 (0x0)

Transmit Identity Data Object (0x47) - (0x1234001000000451c400045103)
  Transmit Identity Data Object
    Record Counts
      Number of UFP Identity Objects                    3 (0x3)
      Number of SOP' (Tethered Plug) Identity Objects   0 (0x0)
    UFP Discover Identity Response
      UFP IDO Header
        USB Vendor ID                0x451 (0x451)
        Modal Operation Supported    True (0x1)
        Product Type                 Undefined (0x0)
        Data Capable as USB Device   True (0x1)
        Data Capable as USB Host     True (0x1)
      Product Vendor Defined Object
        BCD Device       0x10 (0x10)
        USB Product ID   0x1234 (0x1234)
      Alternate Mode Adapter VDO
        USB SS Signalling       USB 2.0 Only (0x0)
        VBus Required           False (0x0)
        VConn Required          False (0x0)
        VConn Power             1 W (0x0)
        SSRx 2 Directionality   Fixed (0x0)
        SSRx 1 Directionality   Fixed (0x0)
        SSTx 2 Directionality   Fixed (0x0)
        SSTx 1 Directionality   Fixed (0x0)
        AMA Firmware Version    0x0 (0x0)
        AMA Hardware Version    0x0 (0x0)
      Certification Test ID   0x451 (0x451)
      UFP IDO VDO #5          0x0 (0x0)
      UFP IDO VDO #6          0x0 (0x0)
    SOP' (Tethered Plug) Discover Identity Response
      SOP' (Tethered Plug) IDO Header
        USB Vendor ID                0x0 (0x0)
        Modal Operation Supported    False (0x0)
        Product Type                 Undefined (0x0)
        Data Capable as USB Device   False (0x0)
        Data Capable as USB Host     False (0x0)
      Product Vendor Defined Object
        BCD Device       0x0 (0x0)
        USB Product ID   0x0 (0x0)
      Cable Vendor Defined Object
        USB SS Signalling         USB 2.0 Only (0x0)
        SOP" Controller Present   False (0x0)
        VBus Through Cable        False (0x0)
        VBus Current Capability   1.5 A (0x0)
        SSRx 2 Directionality     Fixed (0x0)
        SSRx 1 Directionality     Fixed (0x0)
        SSTx 2 Directionality     Fixed (0x0)
        SSTx 1 Directionality     Fixed (0x0)
        Cable Termination Type    Both Ends Passive, VConn Not Required (0x0)
        Cable Latency             reserved (0000b) (0x0)
        Type-C Plug/Receptacle    Plug (0x0)
        Type-C to Type-A/B/C      Type-A (0x0)
        Cable Firmware Version    0x0 (0x0)
        Cable Hardware Version    0x0 (0x0)
      Certification Test ID             0x0 (0x0)
      SOP' (Tethered Plug) IDO VDO #5   0x0 (0x0)
      SOP' (Tethered Plug) IDO VDO #6   0x0 (0x0)

User Alternate Mode Config (0x4a) - (0x0)
  User Alternate Mode Config
    General Settings
      User VID Enabled                             False (0x0)
      User Alternate Mode VID (Vendor ID)          0x0 (0x0)
      User Alternate Mode Billboard String Index   0x0 (0x0)
      User VID Mode 1 Enabled                      False (0x0)
      User VID Mode 2 Enabled                      False (0x0)
      User VID Mode 3 Enabled                      False (0x0)
      User VID Mode 4 Enabled                      False (0x0)
    User Alternate Mode #1 Settings
      Mode Value                                   0x0 (0x0)
      User VID Mode Autoentry Enabled              False (0x0)
      Automatically Send VDM on Mode Entry         False (0x0)
      Load App Config set On Mode Entry and Exit   False (0x0)
    User Alternate Mode #2 Settings
      Mode Value                                   0x0 (0x0)
      User VID Mode Autoentry Enabled              False (0x0)
      Automatically Send VDM on Mode Entry         False (0x0)
      Load App Config set On Mode Entry and Exit   False (0x0)
    User Alternate Mode #3 Settings
      Mode Value                                   0x0 (0x0)
      User VID Mode Autoentry Enabled              False (0x0)
      Automatically Send VDM on Mode Entry         False (0x0)
      Load App Config set On Mode Entry and Exit   False (0x0)
    User Alternate Mode #4 Settings
      Mode Value                                   0x0 (0x0)
      User VID Mode Autoentry Enabled              False (0x0)
      Automatically Send VDM on Mode Entry         False (0x0)
      Load App Config set On Mode Entry and Exit   False (0x0)
    Autosend VDM Data
      Autosend VDM VDO Count         0 (0x0)
      Autosend VDM VDO 1 Data        0x0 (0x0)
      Autosend VDM VDO 2 Data        0x0 (0x0)
      Autosend VDM VDO 3 Data        0x0 (0x0)
      Autosend VDM VDO 4 Data        0x0 (0x0)
      Autosend VDM VDO 5 Data        0x0 (0x0)
      Autosend VDM VDO 6 Data        0x0 (0x0)
      Autosend VDM Vendor Use Data   0x0 (0x0)

Display Port Capabilities (0x51) - (0x60001001c4603)
  Display Port Capabilities
    Enable Display Port SID                       True (0x1)
    Enable Display Port Mode 1                    True (0x1)
    Port Capability                               DP DFP_D only (0x2)
    DisplayPort Signalling                        DP 1.3 (0x1)
    Receptacle Indication                         Receptacle (0x1)
    USB2.0 Signalling Not Used                    False (0x0)
    DFPD Receptacle or UFPD Plug Pin Assignment   C, D, E (0x1c)
    UFPD Receptacle or DFPD Plug Pin Assignment   (none) (0x0)
    Multifunction Preferred                       True (0x1)
    Mux Swap                                      False (0x0)
    DisplayPort Mode Auto Entry Allowed           False (0x0)
    Billboard Index                               6 (0x6)

Intel VID Config Register (0x52) - (0x500000000000000)
  Intel VID Config Register
    Intel VID Config Set
      Enable Intel VID                     False (0x0)
      Enable Intel Thunderbolt Mode        False (0x0)
      Thunderbolt Vout 3V3 Required        False (0x0)
      Thunderbolt Emarker Override         False (0x0)
      AN Minimum Power Required            False (0x0)
      Thunderbolt Mode Autoentry Allowed   False (0x0)
    Adapter Mode Response
      Legacy TBT Adapter   False (0x0)
    Cable Mode Response
      Cable Speed                0b000 (0x0)
      Cable Generation           0b00 (0x0)
      Cable Type                 0b0 (0x0)
      Active Cable               False (0x0)
      Cable Training Supported   False (0x0)
    Billboard Index   5 (0x5)

Texas Instruments VID Config (0x54) - (0x1045100070203)
  Texas Instruments VID Config
    Enable Texas Instruments VID   True (0x1)
    Enable PDIO Mode               True (0x1)
    Enable PDIO Mode Autoentry     True (0x1)
    Message Index                  0b00000111 (0x7)
    PDIO Signature                 0b00000000000000010000010001010001 (0x10451)

GPIO Event Map (0x5c) - (0x83000000000000000000000082810003bff00000000000000000000000000000000000000000000000000000400f)
  GPIO Event Map
    Settings for GPIO #0
      Output Enable               True (0x1)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      GPIO (0x0)
      Mapped Event                Output Enabled Without Event (0x-1)
    Settings for GPIO #1
      Output Enable               True (0x1)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      GPIO (0x0)
      Mapped Event                Plug Event (0x0)
    Settings for GPIO #2
      Output Enable               True (0x1)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      GPIO (0x0)
      Mapped Event                Port Connected CC2 (Cable Orientation Event) (0x1)
    Settings for GPIO #3
      Output Enable               True (0x1)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      GPIO (0x0)
      Mapped Event                Either DP or USB Event (0xd)
    Settings for GPIO #4
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    Settings for GPIO #5
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    Settings for GPIO #6
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    Settings for GPIO #7
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    Settings for GPIO #8
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    Settings for GPIO #9
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    Settings for GPIO #10
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    Settings for GPIO #11
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    Settings for GPIO #12
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    Settings for GPIO #13
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    Settings for GPIO #14
      Output Enable               True (0x1)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      GPIO (0x0)
      Mapped Event                Output Enabled Without Event (0x-1)
    Settings for GPIO #15
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    Settings for GPIO #16
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    Settings for GPIO #17
      Output Enable               False (0x0)
      Interrupt Enable            False (0x0)
      Initial Value               0b0 (0x0)
      Open Drain Output Enable    False (0x0)
      GPIO Output Level           VDDIO (0x0)
      Internal Pull Down Enable   False (0x0)
      Internal Pull Up Enable     False (0x0)
      Map Pin to GPIO or ADC      ADC (Hi-Z) (0x1)
      Mapped Event                Disabled (0x-2)
    GPIO Event #0 -- Plug Event
      GPIO Number    GPIO 1 (0x1)
      Event Enable   True (0x1)
    GPIO Event #1 -- Port Connected CC2 (Cable Orientation Event)
      GPIO Number    GPIO 2 (0x2)
      Event Enable   True (0x1)
    GPIO Event #2 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #3 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #4 -- Source (1) / Sink (0) / Unattached (High-Z) event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #5 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #6 -- Fault Condition (Active Low) Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #7 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #8 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #9 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #10 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #11 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #12 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #13 -- Either DP or USB Event
      GPIO Number    GPIO 3 (0x3)
      Event Enable   True (0x1)
    GPIO Event #14 -- DP Mode Selection Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #15 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #16 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #17 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #18 -- Supply P5V Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #19 -- Supply HV Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #20 -- Supply HVE Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #21 -- Supply PPCable Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #22 -- Attached (Active Low) Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #23 -- VBUS Detect Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #24 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #25 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #26 -- reserved
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #27 -- P5V Overcurrent Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #28 -- Sink (1) / Source (0) Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #29 -- USB3 Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #30 -- USB2 Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)
    GPIO Event #31 -- 2-lane DP Event
      GPIO Number    GPIO 0 (0x0)
      Event Enable   False (0x0)

Miscellaneous Configuration (0x5e) - (0x444d4321444d4321444d4321444d432102020000444d4321444d4321444d4321444d432102020000444d4321444d4321444d4321444d43210202000000300018)
  Miscellaneous Configuration
    Miscellaneous Configuration
      DP Hot Plug Detect GPIO      GPIO 4 is HPD Transmit and Receive (0x3)
      External Reset from MReset   False (0x0)
      External Reset Polarity      False (0x0)
      Ignore Good CRC Mismatch     False (0x0)
      Lock 3V3 Output              False (0x0)
      Use 3V3 for I2C1 Level       True (0x1)
      Use 3V3 for I2C2 Level       True (0x1)
    App Config Group 1 Settings
      App Config Mask, GPIO Low Transition or User AM Exit     0x0 (0x0)
      App Config Mask, GPIO High Transition or User AM Enter   0x0 (0x0)
      Command Channel to use for Command (not Task) Slot       CMD3 (0x1E) (0x2)
      Reserved                                                 Reserved, Set 0 (0x0)
      Command Channel to use for Command or Task Slot          CMD3 (0x1E) (0x2)
      Reserved                                                 Reserved, Set 0 (0x0)
      Alt Mode Entry / GPIO High 4CC Command (not Task)        !CMD (0x444d4321)
      Alt Mode Entry / GPIO High 4CC Command or Task           !CMD (0x444d4321)
      Alt Mode Exit / GPIO Low 4CC Command (not Task)          !CMD (0x444d4321)
      Alt Mode Exit / GPIO Low 4CC Command or Task             !CMD (0x444d4321)
    App Config Group 2 Settings
      App Config Mask, GPIO Low Transition or User AM Exit     0x0 (0x0)
      App Config Mask, GPIO High Transition or User AM Enter   0x0 (0x0)
      Command Channel to use for Command (not Task) Slot       CMD3 (0x1E) (0x2)
      Reserved                                                 Reserved, Set 0 (0x0)
      Command Channel to use for Command or Task Slot          CMD3 (0x1E) (0x2)
      Reserved                                                 Reserved, Set 0 (0x0)
      Alt Mode Entry / GPIO High 4CC Command (not Task)        !CMD (0x444d4321)
      Alt Mode Entry / GPIO High 4CC Command or Task           !CMD (0x444d4321)
      Alt Mode Exit / GPIO Low 4CC Command (not Task)          !CMD (0x444d4321)
      Alt Mode Exit / GPIO Low 4CC Command or Task             !CMD (0x444d4321)
    App Config Group 3 Settings
      App Config Mask, GPIO Low Transition or User AM Exit     0x0 (0x0)
      App Config Mask, GPIO High Transition or User AM Enter   0x0 (0x0)
      Command Channel to use for Command (not Task) Slot       CMD3 (0x1E) (0x2)
      Reserved                                                 Reserved, Set 0 (0x0)
      Command Channel to use for Command or Task Slot          CMD3 (0x1E) (0x2)
      Reserved                                                 Reserved, Set 0 (0x0)
      Alt Mode Entry / GPIO High 4CC Command (not Task)        !CMD (0x444d4321)
      Alt Mode Entry / GPIO High 4CC Command or Task           !CMD (0x444d4321)
      Alt Mode Exit / GPIO Low 4CC Command (not Task)          !CMD (0x444d4321)
      Alt Mode Exit / GPIO Low 4CC Command or Task             !CMD (0x444d4321)

Sleep Control Register (0x70) - (0x0)
  Sleep Control Register
    Sleep Mode Allowed            False (0x0)
    Delay 100 mS Before Sleep     False (0x0)
    Delay 1000 mS Before Sleep    False (0x0)
    Delay 30000 mS Before Sleep   False (0x0)
    Sleep on 5V non-PD Load       False (0x0)
    I2C Relax Response Level      0b00000000 (0x0)
